My orange pi plus can't connect sata hdd.

garyang

I received sata/power cable yesterday.
(like this :http://www.aliexpress.com/item/R ... 2010308.4.20.oXhpii)
I've tried to connect to orange pi plus, It does not seem to be working .
I tested both ext3 and ext4 partition. I used Raspbian and Debian Server.
I also connected sata data cable and power cable separately.
but, useless.....T.T...

Here is part of dmesg

[   12.461140] scsi 1:0:0:0: Direct-Access     USB TO I DE/SATA Device   0009 PQ: 0 ANSI: 0
[   12.472181] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   12.474870] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[   12.475982] sd 1:0:0:0: [sda] Asking for cache data failed
[   12.475991] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   12.480399] sd 1:0:0:0: [sda] Test WP failed, assume Write Enabled
[   12.481625] sd 1:0:0:0: [sda] Asking for cache data failed
[   12.481634] sd 1:0:0:0: [sda] Assuming drive cache: write through
[   12.481643] sd 1:0:0:0: [sda] Attached SCSI disk
[   15.788932] ehci_irq: highspeed device disconnect
[   15.789042] usb 3-1: USB disconnect, device number 3
[   16.631872] gmac0: probed
[   16.634919] gmac0 gmac0: eth0: eth0: PHY ID 001cc915 at 0 IRQ poll (gmac0-0:00)
[   16.691932] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   18.451729] ehci_irq: highspeed device connect
[   18.660268] ehci_irq: highspeed device disconnect
[   18.720042] usb 3-1: new high-speed USB device number 4 using sunxi-ehci
[   18.790048] hub 3-0:1.0: unable to enumerate USB device on port 1
[   18.796811] ehci_irq: highspeed device disconnect
[   21.265379] ehci_irq: highspeed device connect
[   21.487548] ehci_irq: highspeed device disconnect

Is this Kenel problem or sata port was broken?
If it is the case that SATA port problem, I have to request a replacement.

Is anybody successful sata port connected to pi plus?

wolftronics

it works for me ...
2.5 "hard disk to be 5v !!!
3.5 "hard disk to be 5v 12v !!!

I made him quickly cord ....

[512519.352978] scsi1 : usb-storage 3-1:1.0
[512520.352584] scsi 1:0:0:0: Direct-Access     TOSHIBA  MK3259GSX        0009 PQ: 0 ANSI: 0
[512520.363837] sd 1:0:0:0: Attached scsi generic sg0 type 0
[512520.364431] sd 1:0:0:0: [sda] 625142444 512-byte logical blocks: (320 GB/298 GiB)
[512520.365442] sd 1:0:0:0: [sda] Write Protect is off
[512520.365452] sd 1:0:0:0: [sda] Mode Sense: 03 00 00 00
[512520.366430] sd 1:0:0:0: [sda] No Caching mode page present
[512520.366439] sd 1:0:0:0: [sda] Assuming drive cache: write through
[512520.369918] sd 1:0:0:0: [sda] No Caching mode page present
[512520.369927] sd 1:0:0:0: [sda] Assuming drive cache: write through
[512520.433401]  sda: sda1 sda2 < sda5 sda6 >
[512520.441561] sd 1:0:0:0: [sda] No Caching mode page present
[512520.447798] sd 1:0:0:0: [sda] Assuming drive cache: write through
[512520.454776] sd 1:0:0:0: [sda] Attached SCSI disk

garyang

wolftronics replied at 2015-5-23 21:04
it works for me ...
2.5 "hard disk to be 5v !!!
3.5 "hard disk to be 5v 12v !!!

Which image did you use for orange pi plus?

wolftronics

should not be to expect ... debian for a server image raspbian only other packages ...
all have the same kernel.

I tested Debian server image.

garyang

wolftronics replied at 2015-5-23 21:37
should not be to expect ... debian for a server image raspbian only other packages ...
all have the  ...

I see.
I also tested it on android.
It doesn't work too.
Clearly, It's H/W problem.
I have to ask to change it.
Thanks for your reply~~~

igorpec

I also tested it on android.
It doesn't work too.
Clearly, It's H/W problem.

Speaking generally. SATA support in stock Android is usually more by accident not by default.

What about some other hard drive and different power supply?

wolftronics

garyang replied at 2015-5-24 13:27
I see.
I also tested it on android.
It doesn't work too.

SATA works perfectly under android. Tested !!!

garyang

igorpec replied at 2015-5-24 16:46
Speaking generally. SATA support in stock Android is usually more by accident not by default.

Wha ...

I've tried 3 kind of HDD 2.5(5400rpm-slim), 2.5(5400rpm), 3.5(5900rpm).
I've also tried change cable.
I've also tried data cable and power cable seperatly  as blow.
I bought 5V/3A DC Adapter for direct power supply.
I spent 2days for this problem.....T.T

garyang

I've solved this problem partially.
I purchased Sata cable that is compatible cubie board.
The cubie sata cable is connected to the power had been opposed to each other .(+, - reversed)
That's my problem.
I pulled out connecter and reverse it.
Now My Sata cable works like cham....^.^
but Independent connection of the power supply and the data is still not working.

garyang

garyang replied at 2015-5-23 21:18
Which image did you use for orange pi plus?

How can you connect 3.5 HDD?
Would you like me to explain in more detail ?